
A popular mineral-based additive is Clonex Solution - that’s what we recommend. But any clean, hydroponic bloom nutrient will work fine. Cutting Edge Solutions Micro & Bloom and General Hydroponics Flora Series Micro & Bloom are popular options in aeroponic cloning, too.
What is the best nutrient for aeroponic cloning?
But any clean, hydroponic bloom nutrient will work fine. Cutting Edge Solutions Micro & Bloom and General Hydroponics Flora Series Micro & Bloom are popular options in aeroponic cloning, too. Don’t worry, we’ll discuss doses in Taking Cuttings & The PermaClone Recipe.
Which bloom nutrients should I add to the cloner?
Adding 1/4 -1/2 strength bloom nutrients (200–600 ppm or EC: 0.4–1.2) to the cloner improves rooting both in speed and volume. We recommend nutrients intended for water culture. Avoid products which will inoculate or feed bacteria and fungi such as amino acids, protein hydrolysates, sugars, carbohydrates, or ‘teas’.
What should I Fill my aeroponics Cloner with?
Think of your aeroponics cloner as a high performance machine. If you fill the tank with low or mid grade, you can’t expect to realize the full potential of the system. Always try to use filtered or rain water to fill the system and keep the pH between 5.5-6.5.
Does aeroponics make sense for clones?
For clones and seedlings – aeroponics makes sense. I tried cloning in DWC with limited success. The cuttings would get waterlogged and rot away before the roots had a chance to develop. Aeroponics can be divided into two categories. Low Pressure Aeroponics – is usually done with a submersible pump.

What nutrients should I put in my cloner?
Adding 1/4 -1/2 strength bloom nutrients (200–600 ppm or EC: 0.4–1.2) to the cloner improves rooting both in speed and volume. We recommend nutrients intended for water culture. Avoid products which will inoculate or feed bacteria and fungi such as amino acids, protein hydrolysates, sugars, carbohydrates, or 'teas'.
Should I add nutrients to clones?
Freshly cut clones have no roots with which to take up nutrients, so feeding is not required until the first young roots have formed and then nutrients should be first applied at quarter strength, increasing to half vegetative strength as the clones become more developed.
How much nutrients do clones need?
Young plants need little to no nutrients to begin growth. A cloning solution from the Perfect Grower feeding chart is a great introduction to a young clone or seedling. If you're using the 1-Parts, 1-Part Grow at 0.5 grams per gallon will work well.
How do you clone with aeroponics?
3:548:043 Secrets How To Clone Plants w An Aeroponic Cloner - YouTubeYouTubeStart of suggested clipEnd of suggested clipProcess secret number two is clean water there are two ways to get clean water throughout yourMoreProcess secret number two is clean water there are two ways to get clean water throughout your entire cloning. Process you can use a hydrogen peroxide. Process which basically oxygenates the water.
Do clones need nitrogen?
Clones need sturdy, carbohydrate-rich fuel. When a plant is fed nitrogen, it will use up to 25 to 30% of its energy to convert those nitrates into a form of nitrogen that plants can use for vegetative growth. Using the plant's energy for growth results in fewer sugars, or carbohydrates, in the stems and leaves.
Should I foliar feed my clones?
Clones and plants in the vegetative stage will greatly benefit from foliar feeding. Since clones have no roots, they will extremely benefit from foliar sprays as it will aid the rooting process.
How much water should I feed my clones?
Every day for one week, fill your water bottle. You will not see any growth of roots in your clone in the first week of its life following transplant.
How do you keep clones healthy?
The first step in getting healthy clones is to start with a healthy stock plant (the plant you will cut from). Your plant should have strong genes, should be free of pests or diseases, and should not be displaying any symptoms of deficiencies or stress. This plant should also be large enough to support cutting from.
How often should I mist my clones?
How Often Should You Mist Your Clones? The second day is the day for cloning, during which the humidity dome must be removed, then the clones will need to be sprayed with water for good measure. At least one day a week should be devoted to doing this. Once your clones are sprayed, attach your dome over them once again.
What is the pH of aeroponic cloning?
Aeroponic Cloning Tips Number Three Always try to use filtered or rain water to fill the system and keep the pH between 5.5-6.5. It is best to keep the Total Dissolved Solids (TDS) low too, for example after adding mild fertilizer or cloning solutions to around 140-210 ppm (0.2-0.3 EC).
What pH do clones need?
Clones do best in both coir and the plastic cubes at a pH of 6.3. Many people use Rockwool starter cubes for cloning.
Is aeroponics better than hydroponics?
Both aeroponics and hydroponics give better results and yield than soil gardening and are suitable for indoor and urban spaces, but aeroponics gives bigger yields, healthier plants, has lower running costs and looks set for future developments, while hydroponics is easier to set up and manage and is suitable for most ...
Should you fertilize new cuttings?
Excessive misting leaches nutrients from the medium more rapidly and can lead to early nutri- tional deficiencies. Apply fertilizer. Frequent misting can rapidly leach out the pre-plant nutrients in most soilless media. Without fertilizer, cuttings can become chlorotic and root development can be delayed.
How do you keep clones healthy?
The first step in getting healthy clones is to start with a healthy stock plant (the plant you will cut from). Your plant should have strong genes, should be free of pests or diseases, and should not be displaying any symptoms of deficiencies or stress. This plant should also be large enough to support cutting from.
How much water should I feed my clones?
Every day for one week, fill your water bottle. You will not see any growth of roots in your clone in the first week of its life following transplant.
How do I know if my clones are healthy?
Look for strong, white roots that protrude from the grow medium.Nitrogen deficiency is alright in small amounts, but don't select a clone where it's too out of hand.Always inspect dispensary clones for mites and other potential pests.
What nutrients should I add to my cloner?
We recommend nutrients intended for water culture. Avoid products which will inoculate or feed bacteria and fungi such as amino acids, protein hydrolysates, sugars, carbohydrates, or ‘teas’. Do not add beneficial bacteria or fungi. We suspect there may be a bacteria or fungi for aeroponics, but have yet to demonstrate strains of interest for long-term effectiveness.
What temperature is best for cloning?
In cloning, warmer temperature speed cell divisions with diminishing returns at 87 °F (30 °C). However, this also speeds growth of bacteria and fungi. Before attempting higher temps, get sterile! Deep Water Culture (DWC) is different than aeroponics. With DWC the goal is the best temps for both oxygenation AND root growth. The convention is currently 65 - 68 °F. We believe this temperature recommendation may increase as techniques improve for effective water treatment.
What nutrients should I feed my mother plant?
Feed mother plants low strength bloom nutrients (TDS: 300 – 400 ppm; EC: 0.6 – 0.8 mS of base nutrients) while maintaining normal doses of Calcium, Magnesium, silicate, and kelp extracts. Aim for a total TDS of 500 – 600 ppm on the 500 scale (i.e. EC 1.0 – 1.2 mS) with additives. The goal is to minimize nitrogen to just above deficiency levels while maintaining all other nutrients and endogenous auxins (rooting) hormones. Lower nitrogen induces increased carbohydrate storage in the stem of mother plants. Silicon nutrients (such as silicic acid or potassium silicate) have been correlated with improved root mass in cuttings when applied to mother plants. There are points of antagonism, so use the intermediate recommended dosage of silicates.
What temperature does cloning take place?
Water Temperature. In cloning, warmer temperature speed cell divisions with diminishing returns at 87 °F (30 °C). However, this also speeds growth of bacteria and fungi. Before attempting higher temps, get sterile! Deep Water Culture (DWC) is different than aeroponics.
Can you inoculate fungi in aeroponics?
Do not add beneficial bacteria or fungi. We suspect there may be a bacteria or fungi for aeroponics, but have yet to demonstrat e strains of interest for long-term effectiveness.
Can you remove fan leaves from a clone?
You may remove the fan leaves to avoid shading other clones but this is not necessary with aeroponics, DWC or bubbleponic cloning. Removing Leaves. Cutting fan leaves has traditionally been intended to decrease transpiration, but that’s not a concern in aeroponics.
Setting Up Your Aeroponics System
Setting up an aeroponics system is a fairly simple process, which means that you can do it all on your own with a few elements such as:
Proper Nutrient Formulation for Aeroponics Plants
When you are growing plants using the technique of aeroponics, you must do everything possible to ensure the plants have all they need for healthy growth.
Maintain Proper pH Balance
If you don’t already know, pH is used to measure the concentration of hydrogen ions within a solution.
Conclusion
Growing plants with aeroponics is quite tricky- but it’s completely worth it if you can get the system set up right.
What is the best way to clean aeroponic cloners?
Hydrogen Peroxide, Alcohol, Bleach or Castile Soap are common household items that have been used with good results in cleaning aeroponic cloners between cycles. Don’t forget to scrub lots and rinse with plenty of fresh, clean water. Above: Spotless. Inside EZ Clone’s Commercial Cloning System.
How to keep pH of aeroponics cloner low?
If you fill the tank with low or mid grade, you can’t expect to realize the full potential of the system. Always try to use filtered or rain water to fill the system and keep the pH between 5.5-6.5. It is best to keep the Total Dissolved Solids (TDS) low too, for example after adding mild fertilizer or cloning solutions to around 140-210 ppm (0.2-0.3 EC).
Why do you need aeroponics for cuttings?
Aeroponic plant propagation systems can root cut plant stems faster and produce healthier larger cuttings because of the increase in oxygen they supply at the cut stem. Of further benefit, is that growers can enjoy excellent rates of success without having to use synthetic rooting hormones (although many growers still like to dip their cuttings first)—that’s right, the extra fast rooting rates means that you can still produce rooted cuttings very quickly without synthetic stimulators; a potential bonus for organic or health minded gardeners.
How often should you replace an aeroponic cloning system?
Making sure that your aeroponic cloning system, ie pump, manifold, sprayers, base, lid and cloning collars (some people replace these every three cycles to play it extra safe) are clean and hygienic is of the upmost importance for ensuring continued cloning success.
How long do cuttings stay in the cloning system?
Often, cuttings will be very happy and content to stay in the cloning system for an additional one to two weeks after rooting. Bigger, healthier transplants will perform better in your future crops.
How long does it take for super pro aeroponics to grow?
SUPER PRO AEROPONIC CLONING TIP: Don’t reduce the vegetation on mother plants by more than 30% per round of taking cuttings. Also give at least 10-14 days for plants to recover and grow again before taking another batch of cut stems for rooting.
Can you transplant aeroponics?
Well, it’s not that you couldn’t transplant sooner successfully, it’s just that your young root systems LOVE the super oxygenated environment they live in while in your aeroponics cloning system. Once cuttings root, some growers will thin out their numbers to “keepers”, selecting for exceptional health and vigour. Often, cuttings will be very happy and content to stay in the cloning system for an additional one to two weeks after rooting. Bigger, healthier transplants will perform better in your future crops.
What pH do you need for cloning in hydroponics?
Unlike soil (which has trace nutrients) cloning/germination in hydroponics requires immediate additions of nutrients. Once you get the pH to 5.5 add:
What temperature should I use for cloning?
Cloning Temperatures and Humidity 1 Water Temp: 68-80F (I prefer 68-72F) 2 Air Temp: 55-80F (ideal range is 70F) 3 Humidity: 45% – 80% (Yes I have cloned down to 45% humidity with this method, just make sure you remove all fan leaves)
What is aeroponics in science?
Aeroponics is the process of growing plants in a mist environment. Often cited as the most efficient method of nutrient uptake by NASA experiments that researched growing high protein beans in space. Aeroponics is new to me as DWC has worked so well I have not had to look into atomizing the nutrient solution. If roots can sit in the nutrient solution 24/7 why bother with water pumps and misting nozzles. For mature plants I still believe aeroponics is not necessary. DWC is so much easier.
How many categories of aeroponics are there?
Aeroponics can be divided into two categories.
How to sterilize a pump?
Luckily sterilization is very easy since the pump does all the work for you. Fill the bucket with 1 gallon of Star San solution (6mL of Star San/Gallon) and run the pump for 5 minutes.
Can you clone plants with Rockwool?
Rockwool and humidity domes have always been synonymous with cloning plants . Although I have had success with using rockwool, there are a number of problems with it in DWC grows. Rockwool holds water, which can become stale and unoxygenated. Traditional humidity domes run at 100% humidity which is an invitation for mold and bacteria to develop. This mold/bacteria can spread quickly in DWC systems.
Can you use an ultrasonic fogger for cloning?
Sidebar: Do Not use an ultrasonic fogger for cloning. My first attempt at aeroponics involved the use of a $17 ultrasonic fogger. These are often used in cool mist humidifiers or reptile foggers. An oscillating ceramic plate atomizes water into particles that are 3-5 microns in size.
How to feed a clone machine?
When feeding your clones, you want to feed them nutrients and water for 30 minutes every 6 hours. So, set your digital timer to come on for 30 mins at 12pm, 6pm, 12am, 6am. Make sure you always use an air stone in the nutrient reservoir and leave the air stone on to aerate the water for 24 hours a day. I always use rockwool formula one (part a&b) as my nutrients to feed my clones. I mix 3 cap fulls of each and add it to the water that has a ph level of 6.0. Once the solution is mixed, simply fill the clone machine with the water, plug into your timer and continue to drain, flush and refill every 5 days with new clean nutrients and water for clones to live a healthy life.
How to care for clones of marijuana?
Watering or feeding marijuana clones or cutting is the most important thing to know when growing mother plants for clones. If you over water or do not water enough, the clones will not root and will die. Knowing what PH levels the water should be at and what nutrients to add to the water is also very important. Once you know the ph levels and nutrients needed for healthy clones to root, you know need to know the feeding schedule to be set on a digital timer.
What is the first step in cloning a marijuana plant?
Nutrients and Water for Clones. Cloning marijuana mother plants requires special nutrients and water for clones to root and grow healthy. Knowing how to cut the clone is the first step. Once you take the clone or cutting, you need to make sure the clone is placed in cloning solution prior to placing it into rockwool or a clone machine.
How to sterilize clone collars?
Rinse clone collars in hot water, scrub off and remove any debris or algae, place back in cloner. Fill cloner reservoir with hot water and 5 ml/gal bleach and run for at least 8 hours. Drain and refill with plain tap water, then run for 15 minutes. Drain and sterilize collars using standard Permaclone methods ( view here ).
What is a clone of a plant?
A “clone” is when a piece of a plant grows its own roots. The new plant is a small but otherwise identical copy of the parent plant.
What does "cup" mean in cloning?
Cup (s) (to hold cuttings before being put in the cloner)
Turbo Klone
This particular cloner comes with a volley of features, making it one of the more expensive models. The Turbo Klone is equipped with a humidity dome to help keep the leaves hydrated. For those who live in warmer climates, the Turbo Klone comes with a fan to ensure temps don’t get too warm and burn the fragile roots and leaves.
Clone King
The Clone King is available in three sizes, 25, 36 and 64 site models. Each site has a neoprene circle that holds the clipping and a plastic net that helps contain the roots and aerate the water. The sturdy light-proof design helps with mold build up and durability.
Oxyclone
The Oxyclone works a little different than other cannabis cloning machines. Instead of water being sprayed on the cuttings from beneath, water is circulated with a pump. The motion of the water helps pull oxygen into the swirling reservoir.
Botanicare Power Cloner
The Botanicare Power Cloner comes in two colors, black and white, and includes a humidity dome to help keep leaves hydrated before roots form. The Botanicare is specially designed to root larger cuttings, and its large design will ensure all your clippings have room to flourish. The unit includes an oxygen pump, with an oxygen rock included.
Viagrow Aeroponic Cloner
This cloner has a unique multi colored neoprene plug flare that will be helpful to growers who want to keep track of different strains in their cloner. The pump has a screen that helps give the Viagrow cloner the reputation of not clogging. The no-leak lid has an optional air pump port, in case an air pump and oxygen stone are right for your grow.
What is the best additive for hydroponics?
A popular mineral-based additive is Clonex Solution - that’s what we recommend. But any clean, hydroponic bloom nutrient will work fine. Cutting Edge Solutions Micro & Bloom and General Hydroponics Flora Series Micro & Bloom are popular options in aeroponic cloning, too. Don’t worry, we’ll discuss doses in Taking Cuttings & The PermaClone Recipe.
What brand of cloning tools are used?
Cloning Tools: fiskars, any brand will do.
What hormones help with rooting?
Hormones. Auxins (rooting hormones) improve rooting time and the number of roots per cutting. But gels and powder wash off in your cloner before they can truly promote prolific root growth. Gels and powders are also time consuming to apply.
Do you need razorblades for clone?
Fiskars. (period) ...people think using a razorblades is necessary. It’s really not - please trust us. Purchase a nice pair of fiskars and dedicate them to your clone space. Keep them sterile. Doing a razor cut on each clone is tedious. PermaClone is about ease of production and eliminating unnecessary and tedious methods.
Can you use oxidizers on cloners?
We use oxidizers at HIGH DOSES to sterilize our cloners, but we can also use some oxidizers in LOW doses to surface sterilize aeroponic cloners AND clones or cuttings. The dosages are low enough to treat your water without hurting unrooted clones - so please pay attention!
